Environment conditions
In order to operate this paddle mixer safely, please install it according to following operating conditions.
(1)Please install this equipment indoors according to following conditions:
Ambient temperature range (-10~+40°C)
Relative humidity range: 30%~85%
Altitude: less than 1000m
Guarantee indoor cleaning and ventilation
Guarantee that the equipment is far away from the corrosive gas, inflammable and explosive gas as well as steam
(2)Power source: as for Voltage and Frequency, please refer to the nameplate; pressure ≧0.6Mpa.
(3)For easy use, operation and maintenance, please check this equipment and reserve enough space for it.
(4)Please place the mixing machinery horizontally.
(5)The vibration to be borne under effects of many complicated environments may not exceed 12 mm∙s.
Description of warning marks
(1)In order to well understand this operation Manual, the safety warning marks are divided into following kinds.
(2)These warning marks have been worked out according to the operating regulations and safety attention points for this equipment. In order to avoid dangerous accidents, this Operation Manual also includes concrete preventive measures. Please operate this equipment according to the instructions based on sufficient understanding of warning marks.
Description of safety marks
(1)Relevant safety marks are pasted on different corresponding positions of this feed mixer, which are property dangerous to personal safety.
(2)All the safety marks are indicated. Please carefully understand and install, adjust, operate, maintain and inspect this equipment.
(3)Please place these safety marks near the equipment.
(4)When these safety marks have fallen off or been damaged, please replace them with new marks.
(5)If you want to order new marks, please contact our company.
Monday, March 9, 2015
Thursday, March 5, 2015
Muyang Extruder Machine Feature
The extruder machinery provides for production of many products with great superiority in comparison with other technologies. Because it almost integrates functions of different equipment in a single process when extruding, the procedures of mixing, extruding, cutting, cooking, forming and drying process in a certain degree can be carried out at the same time.
Extrusion has the following functions and features:
(1) Multi-functionality of the equipment Multi-functionality of the equipment presents as suitable for processing of different materials and able to achieve different ripening degrees (or extrusion degrees) as required when processing the same material. The reasons for one extruder able to achieve multifunction include the following three aspects:
①The screw configuration applies combined-type structure, which can provide different shearing forces for materials through changing some simple rod configurations;
②There are sorts of discharging devices and the discharging area of materials can be adjusted as required.
③In production, the processing parameters of the extruder can be adjusted as required.
(2) Uniqueness of the product
Other technologies are difficult or cannot produce products and products in certain shapes produced by this extruding operation.
(3) High-quality of the product
This extruding operation is extremely effective for high-temperature and short-period processing, it is provided with a better nutrition improvement while effectively reducing different anti-nutritional factors in products and sterilizing.
(4) Effective utilization of energy
Ripening degree of products through this extrusion operation are improved greatly. Compared with the other processing technologies or modes, extrusion can ripen material in a great degree, sufficiently use steam and reduce power consumption, and thus process cost can be saved.
(5) Minimum industrial wastewater
This extruding can effectively avoid industrial wastewater; this is an outstanding advantage for feed machinery manufacturers bearing the increasing pressure for reducing influences of production activities on surrounding environment.
Extrusion has the following functions and features:
(1) Multi-functionality of the equipment Multi-functionality of the equipment presents as suitable for processing of different materials and able to achieve different ripening degrees (or extrusion degrees) as required when processing the same material. The reasons for one extruder able to achieve multifunction include the following three aspects:
①The screw configuration applies combined-type structure, which can provide different shearing forces for materials through changing some simple rod configurations;
②There are sorts of discharging devices and the discharging area of materials can be adjusted as required.
③In production, the processing parameters of the extruder can be adjusted as required.
(2) Uniqueness of the product
Other technologies are difficult or cannot produce products and products in certain shapes produced by this extruding operation.
(3) High-quality of the product
This extruding operation is extremely effective for high-temperature and short-period processing, it is provided with a better nutrition improvement while effectively reducing different anti-nutritional factors in products and sterilizing.
(4) Effective utilization of energy
Ripening degree of products through this extrusion operation are improved greatly. Compared with the other processing technologies or modes, extrusion can ripen material in a great degree, sufficiently use steam and reduce power consumption, and thus process cost can be saved.
(5) Minimum industrial wastewater
This extruding can effectively avoid industrial wastewater; this is an outstanding advantage for feed machinery manufacturers bearing the increasing pressure for reducing influences of production activities on surrounding environment.
Wednesday, March 4, 2015
Muyang Grinder Mill Repair and Maintenance
Repair and maintenance cannot be ignored while using the machine, only do the job, can the machine operate well and long. Then how to repair and maintain is very important, here is some tips:
Operate according to the operating method strictly. Each shift should well do necessary inspection and cleaning work.
The bearings of the grinding machinery shall be dismounted and cleaned once after 1000 hours working, and the grease shall be replaced at the same time and lithium base molybdenum disulfide shall be applied. Only 1/2-3/4 space inside the bearing cap can be filled with grease. The old grease should be cleared up before adding new grease. If too much grease is filled, the bearings will be overheated. When the bearings are severely heated or the grease outflows out, stop the machine immediately to deal with the troubles.
The damaged or severely worn parts shall be repaired or replaced in time. If the rotor parts (except pins and hammers) are to be disassembled and replaced, balance calibration must be conducted after reassembling. The dynamic balance quality shall be verified in accordance with the balance accuracy grade G 6.3 for rigid rotors of National Standard GB9239-1988. Additionally, the difference between the total masses of the hammers of two symmetrical groups in radial direction should not exceed 5 g.
If the animal feed machine is to be halted for a long time, it must thoroughly cleaned both inside and outside so as to avoiding rusting and screen blockage.
The machine is directly driven through an elastic pin coupling, which should be installed very carefully after maintenance or repairing so as to avoiding the effects of precision deviation on machine running (see Table 5). After installation, the coupling should be checked to ensure that the height deviation between the two halves of the coupling ＜0.2 mm, and the misalignment＜1° and the clearance (S) between the two halves 4-6mm.
The bearings of the grinding machinery shall be dismounted and cleaned once after 1000 hours working, and the grease shall be replaced at the same time and lithium base molybdenum disulfide shall be applied. Only 1/2-3/4 space inside the bearing cap can be filled with grease. The old grease should be cleared up before adding new grease. If too much grease is filled, the bearings will be overheated. When the bearings are severely heated or the grease outflows out, stop the machine immediately to deal with the troubles.
The damaged or severely worn parts shall be repaired or replaced in time. If the rotor parts (except pins and hammers) are to be disassembled and replaced, balance calibration must be conducted after reassembling. The dynamic balance quality shall be verified in accordance with the balance accuracy grade G 6.3 for rigid rotors of National Standard GB9239-1988. Additionally, the difference between the total masses of the hammers of two symmetrical groups in radial direction should not exceed 5 g.
If the animal feed machine is to be halted for a long time, it must thoroughly cleaned both inside and outside so as to avoiding rusting and screen blockage.
The machine is directly driven through an elastic pin coupling, which should be installed very carefully after maintenance or repairing so as to avoiding the effects of precision deviation on machine running (see Table 5). After installation, the coupling should be checked to ensure that the height deviation between the two halves of the coupling ＜0.2 mm, and the misalignment＜1° and the clearance (S) between the two halves 4-6mm.
Tuesday, March 3, 2015
Setting Up an Animal Feed Manufacturing Company
Animal feed manufacturing plays a vital role in the overall food production industry. It's a very active business and its players are always in dynamic interaction.
If you want to start an animal feed production, then our guide can help you understand the basic facts about how this business operates.
Animal feed manufacturing is a billion-dollar industry, according to the American Feed Industry Association. Feeds are so important in raising poultry, hogs, and livestock that some breeders even have their own feed manufacturing operation on-site. If you are planning to start a feed manufacturing business, you must understand that this is a capital-intensive venture.
You would need a lot of money to buy manufacturing machinery (automatic bagging scale, boilers, computer process control, conveyors, mixers, dryers, scales, extruder, and 9HT feed mixer and grinder), computer technology, and vehicles for transporting raw materials and finished products. Another consideration in this business is the huge inventory investment. Feed machinery manufacturers usually take advantage of fluctuations in feed ingredient prices by buying in bulk when prices are low; or by contracting for supplies months ahead.
If you want to start an animal feed production, then our guide can help you understand the basic facts about how this business operates.
Animal feed manufacturing is a billion-dollar industry, according to the American Feed Industry Association. Feeds are so important in raising poultry, hogs, and livestock that some breeders even have their own feed manufacturing operation on-site. If you are planning to start a feed manufacturing business, you must understand that this is a capital-intensive venture.
You would need a lot of money to buy manufacturing machinery (automatic bagging scale, boilers, computer process control, conveyors, mixers, dryers, scales, extruder, and 9HT feed mixer and grinder), computer technology, and vehicles for transporting raw materials and finished products. Another consideration in this business is the huge inventory investment. Feed machinery manufacturers usually take advantage of fluctuations in feed ingredient prices by buying in bulk when prices are low; or by contracting for supplies months ahead.
Monday, March 2, 2015
Muyang Steel Structure
Steel is cost effective, structurally sound and manufactured to strict specifications and tolerances. It is easy to modify, install and offers design flexibility. It allows for improved quality of construction and less maintenance, while offering improved safety and resistance.
From designing to construction following AISC standard, Muyang has proved itself as a reliable steel structure building construction partner by delivering factory buildings, warehouses, high buildings, airports, gymnasiums, conference halls and bridges.
Muyang's Quality Management System (QMS) ensures that we deliver a consistent high quality;
ISO certified: 9001:2008 for designing, manufacturing, fabrication and installation of steel structure and turnkey projects.
Certified Grade 1 Structural Steel Fabricator, and Grade 2 Integrated Engineering & Design Company;
Efforts are especially focused on delivering steel structure buildings, warehouses and other steel structural products such as rising towers and catwalks for feed mills, rice mills grain storage terminals and other facilities in agro-industry.
From designing to construction following AISC standard, Muyang has proved itself as a reliable steel structure building construction partner by delivering factory buildings, warehouses, high buildings, airports, gymnasiums, conference halls and bridges.
Muyang's Quality Management System (QMS) ensures that we deliver a consistent high quality;
ISO certified: 9001:2008 for designing, manufacturing, fabrication and installation of steel structure and turnkey projects.
Certified Grade 1 Structural Steel Fabricator, and Grade 2 Integrated Engineering & Design Company;
Efforts are especially focused on delivering steel structure buildings, warehouses and other steel structural products such as rising towers and catwalks for feed mills, rice mills grain storage terminals and other facilities in agro-industry.
Subscribe to:
Posts (Atom)